1990 Volvo 740/960 Door Clip

Needed an door clip for Volvo 740 and 960 so heres a basic design that should snap in. Copied from a 960. Takes about 10 minutes to print. PETG recommended but i made it in PLA.
Update: Made a new version that looks more like the original now when i have more experience of 3d modeling. One is like original and one is with a pulltab so you can easier remove it with pliers. can be a pain on stock tab.


1990 Volvo 740 Door Clip Pin

The pins that hold the front door panel in my Volvo 740 estate were broken and the panel was loose.
I designed the original pin but the plastic didn't had the strength to hold. So I modified the original pin. The custom part has a thread instead of a spring and a nut is used to secure it from the inside of the door structure.
So far this is holding the panel very well.
The original and custom parts are attached.
Enjoy.


2004 General Motors Radio Radio Equalizer Knobs

The original knobs on the radio all split down the middle, so after trying unsuccessfully to find more in various junkyards, I decided to design new ones and print them. After they were done, I put some white paint I had laying around and brushed some into the recessed line to see where it was pointing better. Each one only takes around 4 minutes to print on a slower speed, use high resolution, infill doesn't really matter. It uses the original tension clips that go on the knob post, so make sure you take them out of the original knobs or off of the post before trying to put them on.


1998 Chevrolet Tahoe Radio Volume Knob

This is a Radio Volume Knob for the radio in a 1995-2002 GM CHEVY TAHOE SILVERADO


1990 Nissan 300ZX T-Top Handle

The original file is great, but I had problems with the handle fatiguing once under load. Went in and thickened it out to make it more stable.
This is for the driver’s side T-Top, you will have to mirror it along Y-axis in your slicer for the passenger side.
Printed using PETG on a Bambu A1
Infill pattern adaptive cubic at 50%


1991 Volvo 940 Door Handle Clips

i needed new clips for the doorhandles on my volvo 960 3.0 so i made this.
printet on the side with supports. give it two swipes on the side with a file to remove support remains and it fits 100%


2006 Volvo XC70 Fog Light Cover

I have been working on my 2006 Volvo XC70 to make a tribute to the Volvo AT Concept. Made up these covers after covering the plastic bumpers with bed liner.


2004 Volvo S60 Center Console Screw

It's the "screw" number 18 in the explosion picture.


1978 Volvo B18/B20 Clutch Centering Tool

Clutch centering tool for classic Volvos with B18 and B20 pushrod engines until 1978. Ten-spline shaft.


1992 Volvo 940 Radio Frame

I wanted a new stereo with Bluetooth and reversing camera for my old Volvo 940 and found a really cheap 2 DIN from China, only known as 7018B.
It doesn't use a metal frame, the radio is put in the frame and then the entire thing is mounted in the car. No screws used, But it tend to bow out at the bottom end, but I might have a fix for that soon.
Edit: Added a lock that slips on the DC outlet behind the panel. Swivel it out behind the panel and tighten the nut on the DC outlet to lock everything together.
The volt meter is a small module, can't fin the exact same anymore but there are very similar looking on eBay, I hope they work. If you use thin wires make sure to add an inline fuse on + so the wires don't catch fire if they short out, or just use solder in some thicker wire.
Update 2021: I have uploaded a model with 2 holes for outlets or compatible modules like phone chargers or volt meters.
The DC outlet is from a local store, but I saw some on eBay looking exactly the same. It had a cover saying "MARINE 12V" ond the text "LOCK POINT" on the outside of the plug.
The stereo name is 7018B and is a really cheap 2 DIN model, if you want to use another stereo make sure it have the right mounting holes and actually fit the frame (check out cad link below).
Created with OnShape: https://cad.onshape.com/documents/9fa29f8e3b761c18b8d866c6/w/b9bebdb79349f763eac27e10/e/d7ce5405a8b101db1755ed24


2016 Volvo V70 Speaker Adapter

Adapter for Aftermarket 6.5" speakers.
Speaker screws directly in to the plastic.
Fits realy good in the orginal mounting holes.
works with alot of volvo cars:
(F=Front and R=Rear)
VOLVO V70 (2014 - 2016) F&R
VOLVO V70 (2008 - 2013) F&R
VOLVO V40 (2012 - 2017) F&R
VOLVO S40 (2008 - 2012) F&R
VOLVO S80 (2014 - 2017) F&R
VOLVO S80 (2007 - 2013) F&R
VOLVO S60 (2014 - 2017) F&R
VOLVO S60 (2011 - 2013) F&R
VOLVO V50 (2008 - 2012) F&R
VOLVO V50 (2004 - 2007) F&R
VOLVO XC70 (2014 - 2016) F&R
VOLVO XC70 (2008 - 2013) F&R
VOLVO XC60 (2014 - 2017) F&R
VOLVO XC60 (2009 - 2013) F&R
VOLVO C30 (2010 - 2013) F
VOLVO C30 (2007 - 2010) F
VOLVO V60 (2014 - 2017) F&R
VOLVO V60 (2011 - 2013) F&R
VOLVO V60 CROSS COUNTRY (2016 - 2017) F&R


1990 Volvo 940 Midvent Gauge

Midvent for volvo 940


2011 Volvo V60 Funnel for Windshield Washer Liquid

This funnel fits exactly into the washer fluid opening of a Volvo V60. It has a double wall that contains 4 channels for venting. Needless to say that you have to print upside down to prevent supports


2000 Volvo S40/V40 Headlight Adjuster

VOLVO S40 / V40 HEADLIGHT ADJUSTER


2006 Volvo XC70 Seat Knob

Adjustment knob for a Volvo 2006 XC70 front seat. Designed and printed it, worked the first time.


2000 Volvo V40 Luggage Cover Hold Clamp

The antique Volvo v40 we recently bought misses some parts.
So why not redesign and print ?
This part should hold the cover in place ( when extracted) over the luggage compartiment.
Please Like before collecting
Thomas
www.3Daybreaker.blogspot.com


2007 Volvo XC70 Luggage Hook

Luggage hooks for the trunk of your XC70. If you are fed up with paying 400+ rubles for a piece of aluminum - print it from plastic with a penny cost price. And yes, there are three versions - close to the original and two more convenient for bags with booze (so that bottles do not rattle on bumps) and for small fishing rods (if you like to carry rods in the car). Good luck.


2013 Volvo V40 Trunk Hook

## Volvo V40 Trunk-hook ##
Designed this Trunk-hook for my Volvo V40. Keeps grocerybags and other stuff from sliding all over the place in the trunk. Made of 3 parts to get maximum strength. Assemble the parts with some suitable screws. You can see the dimmensions of the screws I used in the pictures. Similar screws will do just fine.
Fasten hook to the baseplate first, tread it into the holes in the trunk, and then secure it in place with the lockplate. The hook is angled 6 degrees onto the baseplate, because the holes in the trunk is about 6 degrees angled.
My V40 is a 2013 model, but I guess it will fit earlier/later V40's also.
If you make this, I would appriciate it if you upload a picture of it! Enjoy! =)


2004 Volvo S40 Boot Upholstery Clip

Volvo s40 ii boot upholstery clip


1990 Volvo 240 Blank Switch Cover

Blank switch cover for Volvo 240.


1990 Volvo 740/940 Ceiling Lamp Clip

Original clip cracked so i made replacement part


2012 Volvo C70 Headliner Clip

Designed this Volvo clip for a friend using TinkerCAD.
Slots into this receiver: https://www.thingiverse.com/thing:4915558 by mi540i.
Printed as oriented with no supports at .12 layer height
Volvo part # 31256449 included in repair kit 31256445


1990 Volvo 740/940 Seat Rail Covers Repair Clips

Volvo 940 / 740 seat rail covers repair clips, glued to original cover with CA, works well.


2005 Volvo S60 Boost Gauge Pod

This is a boost gauge pod (52mm) for Volvo P2 S60/V70 (maybe other models too). There are a few options to choose from - with R logo or without, sunked-in gauge or not.
Sunked-in design is based on my boost gauge and might not work for you (outer diameter of boost gauge 58mm and 10mm deep).
I 3D scanned cars interior for the pod to fit perfectly between A-pillar and dashboard. Vacuum hose (8mm outer diameter) comes from the back and is routed through the corner of window/A-pillar/dashboard.
Pod has two protrusions on the side for attachment. Just insert it in the gap between dashboard and A-pillar.
Sandpaper, filler, primer and paint is always an option!


2008 Dodge Charger Auxiliary Switchboard

Have you ever wished you could have switches in your early LX car? Well now you can! I provided 4 files, basically its provided in one or two parts, with or without the "Daytona" logo. I printed it in two pieces on a Lulzbot mini 1.03 with the High Detail 0.18mm preset with scaffolding. I mounted it with zipties as seen in the photo and its pretty secure. Feel free to modify/distribute to your hearts content


2009 Dodge Charger Visor Hook

Visor hooks for the 2009 - 2010 (maybe all years above 2008?) Dodge Charge (300?) have large rods. The only ones you can buy are for smaller rods and will not work. This is a replication (thanks to Tinker3D) and works for mine (2009 Charger).


2017 Dodge Journey Oil Filter Cap Remover

My Dodge Journey 2017 oil filter is located on top beside the engine.
You will need a wrench socket to turn the cap and extract the oil filter inside.
Well, not everyone has a wrench with specific socket for this cap, so the idea was to have one and must be portable and can be put away easily. There is no need to fully close tight, just a snug hand tight is all it need and this device i'm sure will do the job.


2010 GMC Yukon Cup Holders

Factory cup holders did not fit our Nalgene water bottles so I made this.
Should fit GM pickups 2007-2013 and Yukon/Suberban/Tahoe 2007-2014.
For temperature resistance I recommend printing in PTEG or similar as PLA may start to warp in the heat.


2004 GMC Yukon Seat Back Latch

I loved the original design, but with my seat backs, the lip was just a little too short to hold up when hitting bumps. And once I started modifying it, I went a little further and upgraded the design a bit! These are pretty easy to replace, just slide the pin out and get these in place! Needlenose pliers are a must.
For printing, print on the side as oriented in the model. Print at 100% fill and you shouldn't need supports. I printed at 0.2mm layer height with zig zag infill. It is very very strong and should last a long time. For heat tolerance, make sure to use PETG, ABS, or ASA.
When you print yours, print out a spare or two just to have, even a couple to give away! Many of these break due to the terrible OEM design.


2004 GMC Yukon Rear Window Switch Case

this is switch case for rear window of GMC Yukon 2001-2006
Part number: 800755
Thanks, Enjoy!


2022 GMC Yukon Tweeter Adapter Plate

Adapter Plate to fit Hertz C26 OE Tweeter into existing A-Pillar Location
For 2022+ GMC Yukon Denali/Suburban with Bost 14-speaker surround system


2001 Chevrolet Tahoe Center Console Cubby

Remixed and modified by merging two files, the 03-06 cubby from zulubravo, and the 99-02 blank by snarkysoundguy717. Took a few trial runs but fit the 2001 Tahoe console I had lying around. Printed with fuzzy skin, spray with your desired interior trim paint. Thank you to both who uploaded those great models!
Links to original files:
- https://cults3d.com/en/3d-model/various/99-02-gmt800-center-console-radio-delete
- https://www.thingiverse.com/thing:4259408


2002 GMC Yukon Center Console Rear Blank Plate

Remixed from the cubby I uploaded before, just a revised version of the blank plate with the key way cut and a little better corner radius.


2014 Chevrolet Tahoe Headlamp Bulb Cover Wrench

A disk that fits over the tabs on the access port cover on the back of the headlight assembly. Slight twist removes this cover but getting a good grip can be challenging with wrist or finger problems. The disk engages the tabs and provides a fluted rim to assist grip. Fusion 360 and Step files included.


2003 Chevrolet Silverado Dash Cubby

Remixed from Buras Prints awesome model, I added the SS logo to mimic the factory SS inserts while still allowing for both blanks to mount switches or use a gauge. Also added a version with a GMC logo for the Sierra/Yukon folks. If you need one without logos, please go download the original model this was remixed from!


1998 Jeep Cherokee HVAC Blend Door Main Gear

This is a replacement main gear for the HVAC blend door actuator that tends to crack and break with age. From what I could find, this gear should also work for the following units as well in addition to some Mercedes-Benz models. List Below.
if you are unsure, disassemble your unit and compare with attached photo and gear. It may work for your use case as well.
When servicing take care to note the orientation of the metal shaft in addition to the blue gear to make sure alignment does not get lost. Install with flat side of gear facing up. Be sure to lubricate with a plastic safe lubricant and reassemble!
Print with the flat side to the bed of the printer with maximum infill. Choose suitable filament that can withstand torque and high heat for reliable operation.
BUICK CENTURY 1997-2005
BUICK REGAL 1988-2004
BUICK SOMERSET 1987
CADILLAC ESCALADE 1999-2000
CHEVROLET BERETTA 1987-1990
CHEVROLET C1500 PICKUP 1995-1999
CHEVROLET C1500 SUBURBAN 1995-1997
CHEVROLET C2500 PICKUP 1995-1999
CHEVROLET C2500 SUBURBAN 1995-1999
CHEVROLET C35 1995-2000
CHEVROLET C3500 PICKUP 1995-2002
CHEVROLET CLASSIC 2004-2005
CHEVROLET CORSICA 1987-1989
CHEVROLET CORVETTE 1997-2003
CHEVROLET EXPRESS 1500 2003-2014
CHEVROLET EXPRESS 2500 2003-2015
CHEVROLET EXPRESS 3500 2003-2015
CHEVROLET EXPRESS 4500 2009-2015
CHEVROLET EXPRESS CARGO 2012-2014
CHEVROLET EXPRESS PASAJEROS 2011-2014
CHEVROLET IMPALA 2000-2003
CHEVROLET K1500 PICKUP 1995-1998
CHEVROLET K1500 SUBURBAN 1996-1999
CHEVROLET K2500 PICKUP 1995-2000
CHEVROLET K2500 SUBURBAN 1995-1999
CHEVROLET K3500 PICKUP 1995-2000
CHEVROLET LUMINA 1990-2001
CHEVROLET LUMINA APV 1990-1991
CHEVROLET MALIBU 1998-2003
CHEVROLET MONTE CARLO 1995-2002
CHEVROLET SILVERADO 2500 2000
CHEVROLET SILVERADO 3500 2002
CHEVROLET TAHOE 1995-2000
CHEVROLET VENTURE 1997-2000
GMC C1500 PICKUP 1995-1998
GMC C1500 SUBURBAN 1995-1999
GMC C2500 PICKUP 1995-2000
GMC C2500 SUBURBAN 1995-1999
GMC C3500 PICKUP 1995-2002
GMC K1500 PICKUP 1995-1999
GMC K1500 SUBURBAN 1995-1999
GMC K2500 PICKUP 1995-2000
GMC K2500 SUBURBAN 1995-1999
GMC K3500 1995-2000
GMC SAVANA 1500 2003-2013
GMC SAVANA 2500 2003-2014
GMC SAVANA 3500 2003-2014
GMC SAVANA 4500 2009-2013
GMC SIERRA 3500 2002
GMC YUKON 1995-1999
JEEP CHEROKEE 1998-2001
JEEP LIBERTY 2002-2005
JEEP WRANGLER 2000-2005
OLDSMOBILE ALERO 1999-2004
OLDSMOBILE CUTLASS 1998-1999
OLDSMOBILE CUTLASS SUPREME 1989-1991
OLDSMOBILE INTRIGUE 1998-2001
OLDSMOBILE SILHOUETTE 1990-2000
PONTIAC GRAND AM 1999-2005
PONTIAC GRAND PRIX 1988-2003
PONTIAC MONTANA 1999-2000
PONTIAC TRANS SPORT 1991-1998


2004 GMC Yukon Tailgate Latch Cover

I have the STL file reach out if you need it or have suggested changes.
I printed with PETG, 30% infill, and tree supports.


2001 Chevrolet Yukon XL Spark Plug Boot Removal Tool

I made this tool for my 01 Yukon XL 1500. The spark plugs boots have a heat shield on them and if those boots have been attached to the spark plugs for a few years they can be a pain to remove. This tool works on all the plugs even the ones with minimal space in the back. I printed in PLA and didn't have an issue.
Instructions: Once printed out, slide the open end over the plug wire and expand it enough to slip over the heat shield until the lip settles into the groove. Then take a pair of pliers (I found needle nose vice grips work well for constant pressure so they don't slide off) and something to pry/leverage the boot off.
I plan to make a video of this sometime. I sold my Yukon so I don't have a demo vehicle :(. I plan to get another later on though. I will also be adding this to my Shapeways so anyone without a printer can still get one. https://www.shapeways.com/product/WED3B5S4N/gm-chevy-spark-plug-boot-removal-tool


2000 Chevrolet Astro Rear Window Mounting Button/Insert

Rear Window mounting insert for the 1995–2005 series of Chevy Astro/GMC Safari vans with hinging rear windows.


1990 Chevrolet Astro Rear Window Hold Open Replacement Link

This is a replacement link for the rear awning type window latch on a 1990 Chevy Astro Van.


2003 Ford Crown Victoria Ashtray Repair Kit

Repair kit for ashtray in crown victoria's or grand marquis. Print in ABS, Hinge part has two files because the larger part requires 3D printing enclosure to print properly and aligns hinge with inside face lip. Grind broken pulltab tips untill pulltab repair part bottom is flush with faceplate.
https://rumble.com/v3b8kli-vso474-c00-crown-victoria-ashtray-repair.html
https://www.zenlabcreations.com/home


2000 Ford Crown Victoria Raspberry Pi Touchscreen Mount

Raspberry Pi 7" Touchscreen mount for my 2000 Ford Crown Victoria automobile. Also accommodates a Raspberry Pi 3 or 4, and a 10amp DC-DC buck converter (listed below).
I designed the mount to install without any modifications to the dash. I am using it to complete an OpenAuto Pro (Android Auto) installation in my vehicle.
Here is a youtube video of the design and implementation of the mount:
https://www.youtube.com/watch?v=Aqlr-1AQtoM
Raspberry Pi Touchscreen - https://www.amazon.com/dp/B0153R2A9I/
Raspberry Pi 4 - https://www.amazon.com/dp/B07TD42S27/
12V - 5V 10amp buck converter - https://www.amazon.com/dp/B01M03288J/


2004 Ford Crown Victoria License Plate Light Camera Fixture

Crown Victoria license plate light fixture modified for LED bulbs and a large backup camera placement. For cameras that use 4 pin micro connector only Use #13 and #103 o-rings in assembly for waterproofing. LED light bulbs from amazon link below. print custom screws for led bulbs. Best material ASA for fixture and screws, TPEflex for gasket. False raft version for better bed adhesion to get a good surface versus using real raft setting.
https://www.zenlabcreations.com/product-page/13n775-mod-crown-victoria-license-plate-led-light-fixture-for-backup-camera
https://www.amazon.com/dp/B09PRP7CH6?ref=ppx_yo2ov_dt_b_product_details&th=1


2004 Ford Crown Victoria Door Switch

This is a remix of the "Crown Victoria door switch fix" models by beniscooking. They've been thickened and the shape and size of the clip portion has been adjusted.
I recommend printing in PETG for strength and temperature resistance. For a more permanent fix, you can glue them in to place. SUPPORTS ARE REQUIRED.


1990 Ford LTD Crown Victoria Rear Window Bottom Trim Clips

I needed replacement trim clips for a project car I was working on. The vehicle requires 8 total clips, and all but 3 were missing. My final print was in PETG, so they came out a little rough visually, but they clipped into place and have been holding well.
Photos show one of the remaining OEM trim clips next to the one printed in PETG.
To print, I used the automatic supports in Prusa Slicer. I oriented the print with the slot facing down, and the clip on its edge (same as the Thingiverse model preview, but with the slot pointed down instead of up).


2003 Ford Crown Victoria LED License Plate Light Adapter

Every single Crown Vic I've seen had bad license plate light. Water damages the light and/or the connector, lens broken or glue didn't hold the two parts together any more, so I made this adapter for an LED conversion. The light has about 3" of cable, so water won't damage the connector any more.
I paid $8 for the set of two LED license plate lights from Temu. The lights are for Nissan Qashqai J11, Primera P12, Pathfinder R51, X-Trail T31, Juke F15, Micra Versa, Infiniti Q50.
Printed from PETG with 100% infill.


2000 Ford Crown Victoria Rear Main Seal Installation Tool

Printed in ASA, scale 100.4 due to material shrinkage with 99% infill. You want a hard solid material for press fitting part. This is to install a rear main ford crankshaft seal for a Ford modular V8 motor. Pressed to a depth of 0.256". Design is imperial inches.


2004 Ford Crown Victoria License Plate Light Backup Camera Mount

Update 5/10/23: the gasket fits perfectly. Light transmission is good with the "solid" version printed in clear PETG. Additional photos of that version added.
Update 5/4/23: added a model for a gasket. Print from TPU. I initially just cut one from gasket rubber I had on hand, but it's red. The OEM gasket might fit, but is usually firmly stuck to the OEM light, whether by intent or time, so here's a new one! It's literally an extrusion of the top mounting surface of the mount with the inner opening offset 0.5mm for clearance. That should be enough, but I will print one up and check soon.
I've also printed up the rev 4.5 in clear, and it looks decent. I'll have to install and see how good or bad the light transmission is.
Update 5/3/23: Added Rev 4.5, and 4.5 Clear. I imported the model into Fusion 360 and extended some surfaces to avoid awkward small insets and weird angles, and added a bunch of fillets for a cleaner appearance. Removed some extraneous surfaces that were artifacts of TinkerCAD's additive process. The "Clear" version features fully enclosed light boxes, intended to be printed in transparent material. I have not printed these yet, so please let me know if anything blows up.
A reversing camera mount for Ford Crown Victorias that replaces the license plate light. It should fit 1998-2012 Crown Vics and Mercury Grand Marquis, possibly Town Cars - I have not looked at the license plate light on those.
It was designed to fit an Atoto reversing camera, but will likely fit a variety of Chinese-made cameras. Mounting holes may differ, of course, and the angle may not be exactly correct depending on the field of view angle of your camera. The large hole on top is for the big honking RCA plug my camera came with to pass through. Many cameras have a much smaller pug that connects to a harness with the standard RCA plug, but this one didn't, unfortunately. Please feel free to modify as necessary for your camera - I'd love to hear about someone else getting use out of this.
The factory license plate light twists right in. I added a second socket and wiring spliced in for even lighting, but the single light is most likely adequate for legality. this was sliced with PrusaSlicer using an AnkerMake M5 profile @ 15% infill, and printed on an AnkerMake M5 using default settings, taking about an hour to print.
This is my first original design, and I'm really happy with how it came out! TinkerCAD is a treat to use for simple designs like this.


2003 Ford Crown Victoria 12v Mount

Police interceptors often come with the center dash ripped out, leaving no 12v adaptor to fill up your tires, etc. This print compresses into the space and is a mount for this cluster: https://www.amazon.com/dp/B0834MTG3X
You'll have to drill into the lip under the dash to make this work. Fasten the mount with sheet metal screws. Fasten the cluster to the mount with m3 socket head screws.


2003 Ford Crown Victoria Bumper Trim

This blocks off one of the grills in the front bumper. Most Vics had them from the factory but they fall off or break. They're the same just flip it over. I'm planning on attaching a cone to it and using it as a brake cooling duct.


2003 Ford Crown Victoria Sun Visor Clips

The original failed at the glue line after a year in the car - figured I could print it sitting flat in a single piece without too much support material. The hook needs support in this orientation so you can't just do buildplate only supports.
Print in PETG with fairly high cubic or gyroid infill to give it a combination of flex and stiffness to clip in. PLA will sag on a summer day.
I got a much nicer surface finish when I printed it laying flat instead of gluing together two halves.


2004 Ford Crown Victoria Spotlight Door Notch Trim

For printer settings see below.
I printed this part of PETG, in the position laid flat. It fits exactly like the original. It's pretty elastic, however the thickness of the material is 1mm. Take your time and your small tools to remove supports, file all the surfaces carefully. I'd recommend to paint it to prevent from sunlight, and to hide the layers.


2017 Mitsubishi Pajero Armrest Latch

2017 Mitsubishi Pajero armrest latch
You need a hot wire to make a hole for the screws. Also, you might need to press on the latch to lock in the arm rest. I used PLA and it works great for me. Hope you like it :)
Note: v2 latch is more sturdy
Print requirements:
- 20% infill should be enough
- Enable support
the rest of the settings is up to you


2004 Mitsubishi Pajero TR4 2Din Frame

Frame/molding to adapt a 7" multimedia center using the original panel.

I attached it with 3M double-sided tape.


2009 Mitsubishi Pajero 12V Socket

Additional 12V socket holder for Pajero front console. (Gen 4 Pajero)


1991 Mitsubishi Montero Cargo Cover Hook

This hook screws into the plastic panels in the cargo area of the Gen1 to secure the pull out cargo cover. You will need to print two hooks. Print with a strong filament that can handle high heat and UV.


2003 Mitsubishi Montero License Plate Light Camera Mount

Didn't see any good options for printing a back up camera mount for a 3rd gen Montero/Pajero so I made one. hope this helps some people!
File includes housing and lens for a clear material.


2005 Mitsubishi Pajero Seat Folding Clip

Seat folding clip replacement for Mitsubishi Pajero Montero.
The model is not an exact copy, but made for easier printing on a printer.
part number MR655388
I used ABS.
Nozzle: 0.25
Height: layer 0.2
Support: Tree. Angle 60
Maybe someone can print it without supports and with a bigger nozzle, but I haven't tested it.


2007 Mitsubishi Pajero AC Lines Holder

If you found a white plastic part fist-size around the leg area in your Pajero then it is a holder for the AC lines that is under the dash, on the right side of the steering rack / above your right knee.
The rest of the broken part will still be there in between the metal AC lines held with a screw.
To fix it:
1) Unscrew the single screw with the small broken plastic part that stayed there
2) super glue the broken part to the bigger part that you found on the floor
3) glue this 3Dprinted insert inside the groove where screw goes
Wait until glue dries and screw in the fixed part back in it's place.
Photo shows it after repair.
Print lying on the "back" / flat.


1999 Mitsubishi Pajero Clutch Alignment Tool

Clutch plate centering tool for Mitsubishi 4M40 (2.8L) engine.


2004 Mitsubishi Pajero/Montero Sport Fog Light Grille Plug

Grille plug in the bumper without fog lights for mitsubishi pajero/montero sport 1999-2004. MR 496689 MR 496690.
Left and right are no different.
Print with supports


2005 Mitsubichi Pajero iO Windshield Wiper Motor to Body Mounting Gasket

The foam gasket on my windshield wiper cover plate had denigrated allowing engine fumes into the cabin. Here is a 3D file for a replacement gasket.


2004 Mitsubishi Pajero Snorkel Head

I created a snorkel head for my Pajero, it'll need scaled to the size of your snorkel pipe.


2012 Mitsubishi Pajero Bumper Mounting Bracket

Bumper in Pajero IV is held by 4 plastic ears on the bottom of the central part.
It is easy to break it during parking etc.
Designed replacement lips fits the factory mounts to the metal bumper. On the front side plastic bumper slides in to the grove. Print small 3-4mm holed and use rivets to fix it.
Quick fix / plug and play. Use PETG or other strong material.


2000 Mitsubishi Pajero iO Trunk Hook

Replacement for trunk hook found on Pinin; Montero; IO; TR4; Shogun; H77W models


2000 Mitsubishi Pajero iO Auxiliary Light Mounting Bracket Spacer – Front Bumper

Spacer for mounting additional headlights in factory holes of bumper reinforcement for Mitsubishi Pajero IO or Pinin


2024 Tesla Model 3 Charger Lock

This is a charger lock for a Tesla. I made this for a buddy of mine so I am not sure which Tesla models it will fit but I believe he has a model 3. This is just a beefed up version of some others I have found on here. The ones I had found were just a bit too flimsy so I wanted to make it stronger and more durable.
I have included 2 variations, one with a lock logo and one without. I was going to add one with a Tesla logo but wasn't sure if this would be copyright infringement.


2020 Tesla Model 3 Charger Adapter Holder

Utilize one of the plastic push pin clips in the trunk to mount this holder for the charging adapter.
I printed in ABS at 20% infill, no supports necessary.
How to install: https://youtu.be/SD9FAFNJass
Newer Model 3s may not have the push pin, but you can still install in that location, details here: https://youtu.be/WfFdlGZh1fw


2020 Tesla Model 3 Trunk Fence

This is a trunk fence tower for the Tesla Model 3. Using two of the object and about 12 feet of bungee cord, it can be used to keep things from sliding around the trunk. You could also use loose bungees with hooks.
(Be careful; PLA is not strong and can stretch or break, and bungees can carry a lot of energy.)
They can be positioned anywhere along the sides of the sub-trunk lid to accomodate different loads.
There are alternatives, such as https://smile.amazon.com/dp/B06VVPWSXM but they can fuzz up your carpet.
20241027: Added STEP file as requested by @rrsn who wants to remix.


2013 Tesla Model S Mobile Charger Mounting Bracket

A simple way to reduce strain on the Tesla Model S mobile charger cord while plugged into an outlet.
Because the 3D printer I have access to isn't large enough to print the bracket as one piece, I designed a top and bottom section. Mount the top bracket to a wall first and then use the mobile charger brick to determine spacing to the bottom bracket.


2017 Tesla Model S Glove Compartment Shelf

This is a shelf for the glove compartment of a Tesla Model S to help keep things organized. It is wide enough to allow space for the charging adapter at the end. It basically allows you to keep sunglasses and other items away from paperwork and placards. Constructive suggestions for improvement are welcome.
Note: I have learned that the original design developed a sag over time. I have made some changes which I hope will minimize that problem. The new model was uploaded on 11/10/17.


2022 Tesla Model Y Floor Vent Grate Guard

Under the seats there are HVAC vents that are just begging for goldfish and jellybeans to get tossed into them, never to be seen again. Print these and place them over the vents to retain airflow but not the ability to lose small snacks in them. They should friction fit ok, use 1/4" 3M VHB tape on the edges if you want a more secure attachment.


2020 Tesla Model 3 Center Console Trash and Storage Bin

A remix on jonco223's design - I have revised the SolidWorks modeling technique to make customizing a bit easier using features like shelling.
The base design is the same, but with slightly thinner walls for quicker printing. When printed from ABS the wall thickness should provide plenty of rigidity. I was able to lengthen the tray slightly after test fitting the original design in the car.
My work-in-progress iteration moves the sunglasses area to the back of the tray, and opens the front into a second bin for trash or throw-in storage. I wouldn't recommend you keep a banana peel in here, but for small receipts, food wrappers, etc, it should work well. The trash bin has a cutout for the console LED, which helpfully lights it up.
I may try flocked contact paper to better blend in with the center console, but this is intended to be covered by the lid when not in use.


2022 Tesla Model Y Rigid Hatch Stops

After picking up my Model Y I noticed that going over bumps or uneven roads there was a significant "boominess" in the cabin that created a low frequency, infrasonic sound that was quite irritating.
After some research, I realized this problem is systemic to a lot of Model S and Model Y models because of slight movement of the rear hatch.
After calibrating my rubber hatch stops with the "envelope trick" (https://www.youtube.com/watch?v=Z4fYt06sfN0), it didn't remove the issue completely.
There was some discussion on Tesla Motor Club forums about making the two hatch stops more rigid to prevent any flex.
Therefore I created these slip-on rigid hatch stops. They are a tight fit (I recommend printing with a 0.4mm nozzle)- if you adjust the size, you'll probably only want to do it by 0.5%
There are several sizes depending on the depth of your rubber stop. I have marked the measurements of various STLs in 0.5mm increments so you can see what size fits best. Either sides of my vehicle's hatch stops were not equal in depth.
Also attached is a parametric Fusion 360 file if you'd like to make subtle adjustments in any parameters.
I haven't done a spectrum analysis with my phone yet, but I do feel that it has improved.
Original Tinkercad is available here:
https://www.tinkercad.com/things/jjZ1nsBbhmq
UPDATE Jan 13/2022:
If you are experiencing still further booming issues and would like a different approach, also please see this modification here https://teslamotorsclub.com/tmc/posts/6314645/


2023 Tesla Model 3 Washer Fluid Funnel

Funnel to fill windshield washer fluid from the Tesla


2021 Tesla Model 3 Center Console Tray

I Remixed this design and to make it a bit longer as well as remover the dividers. Fits very nicely in the center console and can slide back so you can still access the storage underneath.


2020 Tesla Model 3 Center Console Tray

Much credit to jonco223 for his original. I added ridges to the bottom to make it easier to pick things up, a brim to support it at the back edges so it's not just friction-fit, and finger grooves in the form of a Model 3 logo to help lift it out.
You'll also see in the finished object photos that I flocked it for a velvety surface. There's some technique involved, and I wasn't perfectly successful, but further attempts should be better.
Hatchbox PLA on a modified Printrbot Simple Metal; black flocking glue and navy flocking powder by Donjer.


2017 Tesla Model 3 Cup Holder Liner

This is a cupholder liner for the Tesla Model 3. If printed in a semi-flexible material, like TPU or Ninjaflex, the side blades will bend to firmly hold the inserted item.
(If printed in a non-flexible material, the side blades will break or prevent you from using the thing. Or, they'll securely hold a very weirdly shaped other thing.)
Also, the shape of this may be useful to other modelers, since (after a ludicrous number of attempts) it is a very precise fit for the interior of the cupholder area. If folks are interested and let me know, I'll throw the core dimensions together on a drawing, or in a STEP, or some such.
If you are printing this for yourself, great. If you are considering having this commercially printed, it may be more cost-effective to just order this very [similar commercial product](https://smile.amazon.com/EVANNEX-Holder-Insert-Tesla-Model/dp/B07TYP8GKV/).
I may tweak this to add anti-suction dimples in the bottom, or to adjust the fin geometry, but I want to live with it for a few days before tweaking. I appreciate feedback from users/makers.
And finally, if you've read this far, you may be interested in [my other Tesla (or non-Tesla) designs](https://www.thingiverse.com/lairdb/designs).


2008 Hyundai Accent Trunk Retainer Pin

Those are the plastic pin you need to hold the inside of the trunk of your accent to the metal.


2022 Hyundai Ioniq EV Charger Wall Mount

EV charger support for Hyundai home plug charger. Easy to put and remove.


2010 Hyundai Genesis Headlight Washer Nozzle Cap

Hyundai Genesis 2010 car headlight washer cap for right side


2018 Hyundai Sonata Arm Rest Storage Organizer

I designed this for my Hyundai Sonata 2018. This is an organizer that goes under the arm rest, and goes right into the hole and fills it up. The pockets are designed for my car odor sprays, lint roller, facial masks, gloves, and just a general pocket to throw stuff in, I like to be organized. :)
For other cars, I would just take out the bottom mat, if it has one, and measure it, if not just measure the bottom of the hole as most of the time they are slanted and get bigger the higher up the hole gets. Make a box in tinkercad with those dimensions and go crazy with the types of pockets you want to add.


2004 Hyundai Elantra Headlight Cover

Headlight protection cover for 2004 model hyundai elantra (xd2). This model is for led headlight assembly. It is not suitable for the use of halogen lamps.


2012 Hyundai i30 Car Mat Clip

I designed this clip to keep my car mat in place. It is designed for a Hyundai i30 but may fit other models.


2001 Hyundai Elantra Door Handle

A decent replacement for the inside door handles for a 2001 Hyundai Elantra.


2012 Hyundai Tuscon Foot Rest Plug

Hyundai foot rest screw cap. This is a screw cap plug for the Hyundai footrest for an IX35/Tuscon. This is for the bottom screw, the top one is a slightly different size. This one may work as a top screw cap. If not, let me know and I'll make a separate cap, alternatively you can tinker your own on TinkerCad (https://www.tinkercad.com/things/d7NeX4jdUG2)
I printed mine in PLA but TPU would be better, the original plugs are rubber.


2010 Hyundai All Models Carpet Mat Clips

Remixed off https://www.thingiverse.com/thing:3113519
To fit Hyundai Car Mat Carpet
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/4qutXTq2jac


2008 Hyundai i10 Seat Release Knob

A back/rear-seat release knob for Hyundai i10 (2008-2010), might apply to other Hyundai models or other cars too.


2003 Hyundai Santa Fe Rear Seat Trim Cover

It is a one-to-one drawing of the trim cover on the inner rear side of Hyundai Santa Fe 2001 - 2002 - 2003 - 2004 - 2005 model vehicles.
It is a ready to print drawing.


2018 Hyundai Kona Fusebox Cover

The fusebox cover in the Hyundai Kona can not be used with an OBD reader plugged into the port due to there not being any room left for it due to the design of the original fusebox cover.
This fusebox cover gives room to plug in a low profile OBD reader or a low profile OBD splitter/extension cable. One version has a holder and window for holding a "Vgate ICar2 ELM327 bluetooth OBD2" reader.


2004 Hyundai Tiburon Shelf Clip

The clip that holds the rear shelf (covering the trunk space) in place. I somehow lost mine, so I quickly modeled this in FreeCAD and printed it.
**Update** The original file was a bit narrower than the real piece (I eyeballed all of the dimensions), but I planned on superglueing it in place anyways, so it worked for me. I have since gone back and revised the file to be much closer to true dimensions. It is still a little different from the OEM part, but very close now.
** Use the tiburon_clip_v3.stl file **


2005 Hyundai Tucson Back Window Handle

Handle for trunk window, made for my 2005 hyundai tucson.


2013 Kia Rio H7 LED Bulb Adapter

It's a H7 adapter for LED bulb. It fit for kia rio and other models. I give the file so you can adjust it as you wish.


2004 Kia Spectra Hood Prop Rod Holder Clip

Hood holder clip KIA spectra.


2022 Kia Forte Rear Window Louvers

These are louvers on the rear window for the kia forte " i have the 2022" it fits pretty good.


2004 Kia Cerato Double Din Car Audio Unit Mount

Mounting L-bars for a 2DIN-sized car stereo unit to Kia Cerato LD/TD (1st generation) also known as Spectra5.
May also fit some other Kia / Hyundai car models.
The mounting is designed for a Chinese Android-based head unit (like one on the picture), which had a "brim", slightly larger than the face panel. Sizes of the mounting are chosen for the "brim" to stay behind the car console, while the front panel to stick out from it. So it may not fit head units of other sizes.
Be wise choosing a material for printing car parts. PLA does not fit for it and can be easily deformed on a heat.
PETG is good and strong enough.
The frame, which appears on the final photo, is [another thing](https://www.thingiverse.com/thing:3146176)


2023 Kia Telluride Purse Hanger

My wife loves her Kia Telluride but has wanted a better means to manger her purse when driving with a passenger in the car. When the passenger seat is occupied, she has no real place to put it.
This thing is a hanger that simply drops into the center cup holders and allows her to hang her purse off the back of the center console.
Her purse stays securely in place while driving, is easily reachable from the driver's seat, and the rear-center cup holders remain fully useable.


2012 Hyundai Elantra Door Locking Repair Kit

It compatible with door locking kia and hyundai 79390-0D000, 79380-0D000, 79490-0D000, 79480-0D000, 79480-2H000, 79490-2H000, 79380-2H000, 79390-2H000


2021 Kia K5 6.5" Speaker Adapter

Speaker adapter to fit 6.5" speakers into a Kia K5 and therefor most likely the Hyundai Sonata (might work with other Hyundai/Kia models, but no guarantees). Please, if you find that these work with other models, leave a note in the comments.
This one is sized specifically for the Kenwood KFC-651. You should adapt the opening and screw holes according to your speaker's dimensions.
I also included an SVG template for cutting gaskets to fit the front and back of the adapter. I cut them from craft foam sheets and glued them on. There is also a channel in the back to install 1/4" window sealing tape if you like.
The hole in the base is to run the wire through.
I originally bought a set of speaker adapters from an online stereo parts store. They sucked. They didn't seal to the speaker or car door. They made the woofers sound dead. These are a HUGE improvement. The speakers sound full and the bass is deep and detailed.


2023 Kia Rio Trunk Lock Gear

A good friend of mine has a broken trunk lock in a Kia Rio X-line car. After disassembling the lock, it was revealed that the gear had broken.
Googling, I realized that this is a common problem with the owners of these cars.
I decided to help a friend and everyone who has this problem.


Kia All Models Front Seat Belt Mount Cover

safety belt plug for KIA
Thanks, Enjoy!


2023 Kia Sportage Armrest Organizer

The armrest of my car was large but not useful.
I designed an organizer to put things like glasses, wallets, etc. I hope it works for you.
STL file has support for 45 degree printing. Looks better and stronger than horizontal printing.
2 walls + %5 infill


2007 Kia Sportage Sunvisor Stopper

Edit: Updated to V3, small changes to fit better the arm of sun visor. Added additional versions that features a slot for M3 35mm bolt for extra rigidity (Even with PETG, in hot days, the little arm still wraps and bends from the sun visors weight). I now use the slim version with the M3 bolt for structural resistance and seems to work fine.
Minor note: Heat the bolt prior screw it in to avoid layer separation.
A common problem with 2007 Kia Sportage's Sun visor is that the tensioning system fails over time and the Visor falls down, usually at an uncomfortable level.
Because my sun visor would not stay closed, I decided to make to make a clip that keeps it closed.
This is my second version, and should hold better even if temperature warping occurs.
NOTE: Use materials that are UV and Heat resistant (eg. ASA)


2015 Kia Sportage Speaker Mount Bracket

Note that this model is in inches. This is a customized speaker mount adapter for a 2015 Kia Sportage. This is designed to fit 6.75 inch speakers. It was made using https://www.thingiverse.com/thing:2924217. I had to add mount tabs to the outside edges.
Since it is in inches you can either use the "Barbarian Units" plugin for Cura or you can scale the model by 2540% in your slicer.
Update 7/8/18: This speaker ring as designed didn't quite work. I have redesigned it, and the new design now works. I've made it 1 inch thick and adjusted the mount screw spacing and rotated the mount tabs to be between the speaker screws. Also moved the wiring slot to a hole in the ring. It is a little small for terminals. I used #10x1/14 mount screws and #8x1 screws for the speaker. The screw holes as printed worked well.
I also used speaker gasket tape which I highly recommend: https://www.amazon.com/Parts-Express-Speaker-Gasketing-tape/dp/B0002ZPLPM/ref=sr_1_3?ie=UTF8&qid=1531112743&sr=8-3&keywords=speaker+gasket.


2006 Kia Cerato Ashtray

Update pending: PLA melted in Australian heat. I will also resize the runners eventually to fit better.
A very rough remix (copy pasta) on another car ashtray. Someone stole my original :(
Shouldn't be too hard to resize for other models
This should fit a Kia Cerato 2006
Should be right to print on just about any setting, but I used:
Nozzle: 0.4mm
Walls: 0.4mm
Height: 1.2mm
Support:
Touching Plate
Infill: 100
Takes a little over 12hrs to print on my Anet A8 at 30mm/sec


2013 Kia Rio Trunk Cover Attachment

replacement parts for trunk cover for kia rio 3 hatchback. compatable with original parts.


2005 Kia Sorento Mirror Gear

I tried to find a pair of gears for my mirrors that where broken and i couldn;t find something nowhere. so or i had to pay for new ones 250$ each or to design and print them. So i design this gear at Tincercad cause im in rookie lever at design 3d parts. tested and working great. Hope this file it will help others that might be at my situation. Enjoy


2022 Hyundai Ioniq EVSE Wall Charger Holder

Fits Ioniq EV, among others.
Lightweight holder for your charger.
Can print without support.


2009 Kia Sedona Van Ceiling Vent

This part replaces the broken ceiling vents in our 2009 Kia Sedona (Part #853172J000TW). While not exactly the same part, it does allow for opening/closing and redirecting the airflow.


2007 Kia Rio Key Fob

KIA Rio 2007-2008 Key Fob.
The original one had a broken case that couldn't latch on to key ring, plus internal button had broken off PCB.
The case is bit difficult to snap together, but somewhat manageable, and key ring hole is a bit too small.
It worked well enough 1st go, so I couldn't be bothered to make anymore changes.
I included the .step file for anyone wanting to make changes in Fusion360.
Printed at 0.05mm layer height with support.
Doge donations: D5cqNG1nHCRWeyFHv5LaJNrMP54MVyM2Az
Much appreciated!


1998 Honda Accord Armrest Clip

Replacement for original Armrest clip


2008 Honda Accord Rear Seat Mounting Clip

Clip that holds the rear seat down to the seat shelf. 1 per side.
Should fit all 8th gen Honda Accord.


2007 Honda Accord Shift Lock Cap

After loose the cap of my Accord 07, I decided to print a new one.
I do recomend to print in a good quality ans with the first botton layer concentric.
Also, I used PETG to not having trouble with hot temperatures of a closed car in the sun.
This is my first upload, please comment!!
Uploading the cad file to anyone who want to remix or change it.


2013 Honda Accord Trunk Trailer Wire Bracket

Bracket for holding trailer wire out of the way in the trunk. Un screw existing bolt/luggage hook and bolt back in with bracket inserted. Made for 9th gen Accord sedan but might work on other models as well.
Wire zip ties to the back of the bracket so, keeping it in place and preventing it from pulling on harness. Then the free end sits in the hook when you are not using the trailer.
Printed in PETG to handle cold weather in Canada.


1999 Honda ["Accord","CR-V"] Dome Light Button

I made this button because I couldn't find it online, it fits perfectly. feel free to use.
Honda crv 1st and 2nd gen
Honda accord 1999


1987 Honda Accord Trunk Cover Clip

My clip is broken so I remodelled it in blender and printed a replacement. Works great.
Print on its side to give the clip arms strength.


2000 Honda Accord Bumper Cover Fender Hanger

This is a bumper cover fender hanger for a 2000 Honda Accord. I'm not sure of the actual name, or how many different years/models/brands this part will work for, but I figured it's one of those stupid little things that are incredibly hard to locate, so might as well share it in case someone else needs it.
Apologies in advance for the orientation of the part. Because of the way the flex locks are situated, the model had to be oriented this way to successfully print the critical parts. So a Raft is definitely needed to print this. I printed mine in PLA, but PETG would've been better, or even ABS.


1991 Honda Accord Door Handle (Inner)

In my country, there are very few Honda Accord 1989-1993 (CB3, CB7) models and finding any part on them is a big problem. That's how I could not find the door handle with the body.
I found the body and handle on the Internet, all separately and they were for other models.
Slightly tweaked for Honda Accord 1989-1993 (CB3, CB7)
This model is for the right side of the car.
For the left side, just make a mirror position
PS 21.02.2022 Fixed hole position and replaced files
В моей стране моделей Honda Accord 1989-1993 (CB3, CB7) очень мало и найти какую либо деталь на них является большой проблемой. Вот так я так и не смог найти ручку двери с корпусом.
Корпус и ручку нашел на просторах интернета, всё по отдельности и они были для других моделей.
Немного подправил под модель Honda Accord 1989-1993 (CB3, CB7)
Эта модель для правой стороны автомобиля.
Для левой стороны просто сделайте зеркальное положение


1986 Honda Accord Trunk Lock Linkage

Trunk Linkage from Lock cylinder to Trunk Latch for a 1986 Honda Accord


2004 Honda Accord Door Lock Hole Cover

When fixing my Honda Accord's door, the piece that goes around the door, broke! So when I went online to find a replacement piece, the cost was $150! for a 20mm piece. This is why I 3D modeled a replacement piece to fix this.


1996 Honda Accord AC Knob

AC Knobs for my '96 Accord. I'm sure they fit other models but I don't know which. Files include the Sharingan Knob that I put in my car but I also included a blank. Dimensions for the cavity in the blank one are:
Diameter: 36.8mm x Height: 6.05mm.
Also included is a painting mask. I used that to paint the red on my sharingan knobs and then hand painted the tomoe black afterwards.
Enjoy


2000 Honda Accord Wiper Fluid Reservoir Cap

This will likely work with other Honda models as well. I printed mine in PLA+ but PLA would likely work just as well. It does get warm under the hood but I don't think it's quite warm enough to cause issues here. I would still check up on it after some time, however.


2014 Honda Accord Screen Glare Shield

i really disliked this screen always getting glare. so i designed a shield that blocks sun glare. the pictures show the regular sized one but i also included a short version in case you want a more discreet / low profile version.
the guard hooks into the cd player slot and is easily removable


2004 Honda Accord Interior Light Cover Clips

ı designed honda accord interior light cover clips. print and glue with hot silicone and use it. :)


1979 Honda Prelude Engine Fuse Cover

1979-1982 Honda Prelude SN, 1977-78 Honda Accord SJ Engine Fuse Cover or Roof. This is an exact copy of the original. Recommended to print in ABS due to heat from engine.
Honda # 38260-671-010
If you would like a printed part but do not have a 3D printer, please email me at Nmitchell_47@yahoo.com and I can ship you one for a small fee. Thanks!
Check out more at G1Preludes.com


2004 Honda Civic Subwoofer Adapter

Remixed to fit my Pioneer Subwoofer in my 9th Gen FB6 Civic Si Sedan. Will fit any 8th or 9th gen civic or accord with the factory 8in subwoofer and any standard 6 hole subwoofer. I designed it in Fusion360 but based the design off of the original. Had to elongate the mounting slots to fit the newer Civic but left them long enough so they should fit the 8th gen.


2002 Honda Accord 6.5 inch Front Speaker Mount

6.5 inch Front Speaker Mount - Honda Accord 1999-2004
Replaces factory speaker mount with larger speaker.
Check for fit and adjust accordingly.


1979 Honda Prelude Window Crank Base

Reproduction part for the window crank handle base. Will fit 1979-82 Honda Prelude, 1978-1989 Accord and 1978-1983 Civic.
Honda # 75343-657-010
If you would like a printed part but do not have a 3D printer, please email me at Nmitchell_47@yahoo.com and I can ship you one for a small fee. Thanks!


2004 Honda Accord Rear Door Cable Holder

This will hold the cable onto the door handle frame when the green plastic cable housing end breaks off. This replaces the metal angle, the mounting hole is printed in but will need an M3x0.5 tap to create the threads.
Just remove the metal angle, and attach the print and then the cable will snap in place.
I printed it with tree supports and the bolt hole on the top. I used PETG-CF, but ABS or ASA may be more suitable...


1995 Honda Civic Trunk Emblem Badge Base

This are bases for flat emblems that are cheap and it can stick to the base just using the included double sided tape. I designed 3 versions for 3 different dimensions:
- 63mm x 54mm (OEM size for the Civic EJ1)
- 68mm x 56mm
- 72mm x 60mm
For fixing the base to the trunk you can use two M3 screws and nuts, I would be better if you use a auto locking nuts on the back and some washer to spread the load into the metal sheet.
Also be sure to use some gasket maker around the bolts so you don't get some water getting into the trunk.
The emblems can be bought on ebay, amazon or aliexpress. A link as example to buy the same emblems I used is:
https://www.ebay.com/itm/284108633183
If you are on Argentina you can ask IRPRacing: https://irpracing.com.ar/producto/emblemas-exteriores-honda-civic-accord-88-00-varios-colores/


2007 Honda Accord Navigation Center Button

That is the Center Button - Joystick for the Honda Accord navigation Unit
and is actually rev.2
made it on Tinkercad using a original one but is not 100% like the original.
Printed with full line support and 8mm brim. time it takes with speed of 50mm is about 33 minutes.
Here is a link to the model itself in tinkercad, so feel free to mod it any way you want.
https://www.tinkercad.com/things/fBIk2Tf76jf
that version is not a 100% tight fit cause it was used for a broken center pin on the navi itself and with a blob of hot glue was the easiest fix.


2004 Honda Accord Nalgene Cup Holder Adapter

Print both parts separately and super glue the top and bottom together. This fits my 2004 Honda Accord cup holder


2005 Dodge Charger Rain Sensor Bracket

Rain sensor windshield mounting bracket for Dodge Charger. Bracket base printed from ABS, attached to windshield with epoxy glue. Clip printed from Nylon which was flexible and strong enough to push out all air bubbles between sensor and windshield.


2006 Dodge Charger Taillight Fastener

after using chair leg ends to hold in my taillights on 2006 charger r/t i finally made new fasteners pretty sure 300 and magnum use same item 2005-2010 afaik


2005 Dodge Charger Lane Departure Camera Bracket

Print with ABS.


1987 Toyota Supra Center Console Latch

Center console latch for an A70 Supra. Only difference from the source is the cutout for the indexing bar on the lid.


1990 Mazda Miata Softtop Latch Cap

This part is designed to replace broken cap of mazda miatas softtop latch.
Original part number is NA01-R1-311.
It was designed to match original part as accurately as possible.
It prints fast, so to achieve durability print with 100% infill.


1996 Mazda Miata Gauge Panel

right now i am in the process of turboing my 1996 Mazda miata and i couldn't seem to find a good way to mount the boost gauge and AFR gauge so i removed the little cubby under the radio and made this to fit in there! hope someone else can get some use of this i know i will!
I used Brass #8 x 3/4 in. Wood Screws to hold mine in and it worked great!


1985 Mazda RX-7 Dash Triangle Vent

It's been years since I've printed this but depending on the surface quality you want then can print bottom down with supports to support the top lip, or top down with no supports. I printed it in ABS. Sorry the initial orientation is not correct but just rotate it 90 degrees on the X axis to lay flat.
In the attached images I've vapor smoothed the part before hitting it with some spray paint. They have been sitting in the car for at least 3 years now and still look great.
This is the drivers side, but just flip it for the passenger side.


2014 Mazda 3 Triangle Bumper Plug

You can mirror the file to get the cover for the opposite side. Print with the flat part on the bed, tabs pointing up. Supports aren't really needed, but you might want to have them for the overhang. Print in a strong and heat resistant plastic, such as PETG.
It isn't a PERFECT fit, but it's not too bad!


1997 Mazda 626 Lifter Gear

Mazda 626 lifter gear
He restored the broken mechanism for the glass lift.
The printed PLA with plastic, a speed of 40 mm / s, is pretty good to see how it behaves when working.
Maybe someone is useful.


1990 Mazda MX5 Handbrake Cover - Cherry Blossom

I made this simple handbrake cover to replace the stock one on my MK1 Mazda MX5.
it features an embossed cherry blossom design.
you can paint it if you choose to do so, id love to see this on yours!


2002 Mazda Miata Window Switch

Well the Miata window switch fingers broke and I don't feel like going out to find one so here we are. This thing is heavily a work in progress. I have it in my car now and its functional. However I was unable to properly size the return spring hole. But it works a whole lot better than the screwdriver I was using to put my window up and down. If anyone knows where I can buy just the plastic switch part and not the whole assembly let me know.


2008 Mazda 3 Power Windows Gear

Gear for Power Window Motor for Mazda 3, 5, 6 2004 - 2012 RX8 , CX7, CX9. My power windows motor's gear wheel had three missing teeths. I disigned the gear using the Gear Generator For Customizer V2.0, The gear fit and works just like the real one.
inspired by http://www.thingiverse.com/thing:393607


1996 Nissan 300ZX 3rd Brake Light Stud Retainer

Back at it for another 300ZX part ! This is a Stud retainer for the 3rd brake light bar on a 1996 Nissan 300ZX. I was replacing the bar that was broken, really common problem on these, and ended up twisting the stud inside of the plastic retainer. Had to destroy the retainer to get the nut removed. Figured I would make one instead of ordering and waiting for another. There are only two of these on this part. I printed multiples in case I messed one up putting it back together. I did not need glue or anything to hold the stud in place as it was a really tight fit.
Printed without support by flipping the part on its end. Very little sagging due to the very short distance that needed bridged.Print settings were 3 shell, .2 layer height, no support, and 85% infill.
Let me know of any questions or concerns. Hope it helps =)


1993 Nissan 300ZX Rear Hatch Latch Trim

Just my design of a rear latch trim piece from a 2 seater 300zx nissan


1990 Nissan 300ZX Cup Holder with Charger

Feel free to remix yourself to fit you needs. You will have to dremel the bezel to make room for the Cup Holder. I did not model to sides of the cup holder. I put an LED into mine and like the look of an open void. Also added USB charger ports which i wired to the stock cigarette lighter wires
Hardware: 4x M4 bolts
4x washers
4x heat set nuts
1x 12V USB C
Car Charger Socket: https://www.amazon.com/gp/product/B08XLKX832/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Printed in PETG


1990 Nissan 300ZX Ignition Bezel

Needed this as mine was missing from my Z32
Print in TPU, it snaps in with a tight fit.


1993 Nissan 300ZX T-Top Release O-Ring

T-Top "release" slider thing falling out? See that little divut there? There's supposed to be a rubber o-ring thing. Printed this in TPU and stretched it on with a little help from a lighter and now it doesn't fall out.
Note: I know USDM models have locks on the T-Tops. I don't know if this will fit on them. My car is a 1989 JDM import.


1990 Nissan 300ZX Wiper Link Bushings

this is parts my car needed,and no more part wil be made at this point


1984 Nissan Z31 AC Gauge Pod

This turns the ac vent right to the steering wheel into a gauge pod to utilize the JJCOCO WATER TEMP GAUGE / ZHSYMX GAUGES and the square voltmeter "Panel Volt Meter - 4.5V to 30VDC" available at adafruit (Product ID: 575)
To install this i recommend retiring the radio and unclip the ac vent from the back, the install of this part its the same as the removal of the oem ac vent.
You WILL need to adjust the model to accomodate different gauges.


1985 Nissan 300ZX Hose-Drain Front T-top

This is a close interpretation of the lower rubber grommet/pass-thru section the forward T-top drain tubes (76990-03P00) on the Nissan Z31 300ZX. The 10mm OD polyvinyl tubing runs down the A-pillar and then is glued into this black rubber piece which then passes thru the sheetmetal. It often can deteriorate, letting water drain into the cabin of the car.
The original part acts as a grommet on either side of the sheetmetal.
Rev2 is a 1:1 test mockup, printed from PETG.
Rev3 is a 1:1 test mockup, with features that should allow it to be sandwiched into the sheetmetal like the original.
If you cannot print flexible filament, maybe use Rev2 and RTV to hold in in place.
If you can print flexible filament, use Rev3...and rtv anyway.


1990 Mazda Miata Door Bushing

My spin on a miata door bushing. Others are too complicated, or the holes are too short. Also I include freecad file for easier editing.
Even pla did the job, but I switched to PETG and it's ok, too.


1991 Mazda Miata HVAC A/C Knob Controls

A/C knob for mazda miata 1989 - 1997


2000 Mazda Miata Gauge Pod

Gauge pod for your mazda miata/mx5 in the crashpad.
Design like Sharka's Gauge Cups


2008 Mazda MX-5 Windscreen Cap Cover

As you know, when you remove these caps/covers the tabs snap off, well they will do at that age.
I had one still on the car held on with 1 clip and blu-tac, so i measured it up and made this little bugger.
It actually fits, first go.


2005 Mazda MX-5 Cam Gear Locking Tool

MX-5 MX5 Miata Cam Gear Locking Tool by BEAVIS


2000 Mazda Miata Hand Brake Sleeve

As shown. I used ABS.


1999 Mazda MX-5 Miata Window Switch Clips/Tabs

These tabs/clips superglue in to fix the broken ones on your window switch. Extremely simple and effective :). This is in a 99 MX5 (NB8A), no idea if it works in others.


2005 Mazda MX-5 Antenna Delete Plug

Simple threaded antenna delete plug for our loved mx-5, use spacer in "trunk side" of plug for tighter fit. If you forgot to plug antenna hole during bodywork this is a great solution :)


1990 Mazda Miata Center Console Delete Cap

A cap to cover the hole left with a removed center console on a 1990-1997 Mazda Miata. It has slight clearance from the transmission tunnel to fit a carpet.


2005 Mazda Miata Trunk/Fuel Lid Levers Cover

Cover for the cables and bolts that attach to the trunk and fuel cap levers at the rear of the transmission tunnel. Fits using original screws.
I didn't have the bed space to make it larger, else I would have made the rear angle larger to better contact the rear firewall.
Inspired by:
Miata Fuel Pull Cover (NA) thing:4545328
josh7owens


1990 Mazda Miata Oil Dipstick Handle

*** Updated and reuploaded as updates meant the first model was unusably small. V2 model should work now!***
Dipstick handle to replace the ever-broken handle on your Miata, MX5 or Eunos! I didn't like any of the other STL offerings online, so I designed this one instead! I have also included a sliced Cura profile I used for my final model in ABS if you'd like to save yourself some time and fire it straight into the printer!
If you found this useful, please donate what you think it is worth to my paypal.me, at https://paypal.me/danobriendesigns?locale.x=en_US to help cover the time of design.
Thanks, and Enjoy! Please feel free to ask any questions, or let me know if you have issues, I'm happy to help!
Updated 11/5/20 - On specific slicer settings, the printer sometimes had trouble printing the overhang, even with supports. That said, the file printed multiple times for me with no issues. Regardless, I made some tiny adjustments and that issue has been ironed out. Let me know if you have any issues!


1990 Mazda MX-5 Window Crank

Mazda Mx5 Na window crank shaped like the OEM before the restilyng.
IMPORTANT:
it must be assembled as in the photos. It is assembled using an M4 low cap steel bolt with a hex socket.
The lever knob comes together but doesn't turn very well. you have to force it in and turn it and after a while it works. It was a work in progress until I discovered aliexpress.
If you like this part please tip me I will use your donation to support my Mx5 build.
If you have question or you want to see my Mx5 search " nomoney_miata " on Instagram.
Thanks


1988 Toyota Supra Front Badge Retainer Clip

The front badge retainer clip has a tendency to rust away. This plastic clip does the same job and will not rust.
Print the clip on its side so the layer lines are aligned properly for the clip to flex like a spring.
This clip is also used to retain the headlight washers in the nose panel.


2000 Mazda Miata Window Roller Guide

Window roller replacement for MX5 Miata, modeled off an original roller from a 2000 NB MX-5.
You'll want 100% infill for obvious reasons.
Exported from blender with measurement in meters as Flashforge's software auto converts meters to millimeters. Original .blend file included as usual for those that need measurement tweaks.


1990 Mazda MX-5 Sequential LED Turn Signals

DISCLAIMER: I'm still perfecting this design and there are some things that need some more tweaking. With that, I am open to any suggestions and constructive criticism. And if you have any questions please ask. Enjoy!!
I wanted cool LED sequential turn signals but didn't want to pay $200+ for a set. I also wanted to use my turn signals as intakes since I have the air filter behind the headlight.
I found these Sequential LED strips on eBay that you can cut to the length you want. My design is basically just a housing and mounting solution for those LED strips.
Also would like to note this is probably not legal in most places,
The running light is white and the turn signal is amber that turns on sequentially. Video here: https://www.reddit.com/r/Miata/comments/hlg1kq/i_made_these_3d_printed_siquential_turn_signals/
See the Instructions PDF for a basic installation guide and some tips.
The turn signals now being LED will make the flasher relay hyperblink. To fix this you can replace a resistor on the relay. I linked the 1M resistors I used below. Here is a write up on how to do it: https://forum.miata.net/vb/showthread.php?t=335534
Hardware: 4x Socket Head M4x12mm
4x M4 Washers
4x M4 Nuts (I used Nylon Lock Nuts so they don't loosen accidentally)
2x Socket Head M5x16mm
2x Fender Washers (Needs to be bigger than a normal washer since the mounting hole is large and to spread out the load. You can make one from sheet metal if needed.)
2x M5 Nuts (Also Lock Nuts would be best)
Sequential LED
Strips: https://www.ebay.com/itm/2pcs-LED-DRL-Daytime-Running-Lamp-Strip-Light-Sequential-Flowing-Turn-Signal/383174835261?_trkparms=aid%3D111001%26algo%3DREC.SEED%26ao%3D1%26asc%3D20160908105057%26meid%3Ddff6cd897ce54454b5379f6997134026%26pid%3D100675%26rk%3D4%26rkt%3D15%26mehot%3Dnone%26sd%3D292032282132%26itm%3D383174835261%26pmt%3D1%26noa%3D1%26pg%3D2380057%26brand%3DUnbranded&_trksid=p2380057.c100675.m4236&_trkparms=pageci%3A2634cad0-be26-11ea-bd5b-74dbd18008f6%7Cparentrq%3A1b234b351730aa119c233dc2fff7b864%7Ciid%3A1
1M
Ohm Resistors: https://www.amazon.com/gp/product/B0185FCM0W/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1
Solder
Connectors: (These are easier than soldering)
https://www.amazon.com/Kuject-Connectors-Waterproof-Electrical-Automotive/dp/B073RMRCC3/ref=sr_1_2_sspa?crid=15KP77VGBQG5&dchild=1&keywords=solder+connectors+with+heat+shrink&qid=1593888262&sprefix=solder+con%2Caps%2C162&sr=8-2-spons&psc=1&smid=ANYCM9RSLDH7Y&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUEzT043SDlESzdGRFJQJmVuY3J5cHRlZElkPUEwOTkxODI2UkJRV0NTVUpLMjdaJmVuY3J5cHRlZEFkSWQ9QTA5Mzg1MDgyS05OQ1NGTUhOSU4xJndpZGdldE5hbWU9c3BfYXRmJmFjdGlvbj1jbGlja1JlZGlyZWN0JmRvTm90TG9nQ2xpY2s9dHJ1ZQ==


2002 Toyota Supra Speaker Adaptor

This fit my rockford fosgate speakers, may not fit yours.


1993 Toyota Supra Cup Holder

This print is to replace the Mk4 Supra ashtray with a cup holder.
Should fit a redbull / pepsi can.
Haven't tested it so pending print/ test.


1983 Toyota Supra Rear Shock Cover

Remake of the Rear Shock Tower Covers for the MK2 Toyota Supra. Could not find them anywhere so decided to make them!


1997 Mazda Miata Double Din Mount

PiDash NA Miata Double Din Mount for Raspberry Pi Official 7" Touchscreen
These files are used to fit a Raspberry Pi Official 7" Touchscreen to the radio opening of a NA Mazda Miata using the provided files to 3D print brackets along with an assortment of M3 nuts and bolts and some of the Miata's factory hardware. I used this to build a "dash" for my TunerStudio gauges but it could also be made into a radio for use with OpenAuto or CrankShaft.
This was tested to fit in a 1997 Miata M Edition. The Miata interior does not have a standard size double din opening and that is what the spacer is for is to take up the area above and below the screen. Different model years and various trim Miatas have multiple versions of the tombstone with different size radio openings so the spacer may not fit all variations. Although the actual hardware that mounts the screen to the radio opening should work across multiple years and most people should be able to modify the spacer to work if needed or source a different tombstone for a clean install.
LH and RH side mounts attach to the screen mount via captive nuts in the screen mount. The slots are designed to use the M3 hardware linked below.
Link for M3
Hardware: binifiMux 360pcs M3 x 4mm / 6mm / 8mm / 10mm / 12mm / 16mm /20mm Pan Head Phillips Machine Screws and M3 Hex Nuts Assortment Kit For Toys RC Models 3D https://www.amazon.com/dp/B08N5TJ2XV
The acc mount is designed to use the same standoffs as the Raspberry Pi which I believe is M2.5.
Note 1: Some of the ribs on the rear of the tombstone will need to be trimmed when fitting it as not to press on the screen. If you make precise cuts, perhaps using some diagonal side cutters, and are careful not to damage the tombstone you should not see any evidence of said cuts when the tombstone is installed.
Note 2: Files should be printed in a filament that can withstand the high temps present in a cars interior such as ASA.
Note 3: Test fit the screen to the screen mount and get it centered before fitting the side mounts. The mounting holes for the screen are slightly offset so if the screen does not appear centered simply remove the screen from the mount rotate the screen mount 180 degrees and reattach. After you know the top and bottom of your screen mount and its orientation you can then proceed to attach the LH and RH side mounts. Most of the holes in the brackets are slotted and allow some adjustment.
Optional parts I used in my build:
Metra 70-7901 Radio Wiring... https://www.amazon.com/dp/B0002BETW2
UWAYKEY
Bluetooth Amplifier Board: https://www.amazon.com/dp/B08HQSXNST
kuman
Breadboard Jumper Wires: https://www.amazon.com/dp/B01L6THEE8
Adafruit 4079 2 x 20
Socket Riser: https://www.amazon.com/dp/B07PPD25MK
CarPiHat: https://www.tindie.com/products/tjd/carpihat-raspberry-pi-car-interface-pcb/
Attribution: This item is a remix of the two below files along with some original content.
https://www.thingiverse.com/thing:2543354
Miata Stereo Universal Double DIN Head Unit Mount
by EMRL September 19, 2017
and
https://www.thingiverse.com/thing:1503651
Raspberry Pi 7" Touchscreen Super Awesome Portable
by DrVegetable April 19, 2016


1985 Toyota Celica Supra Trim Piece

Had to Replace this trim piece So i made it.
PLA
100% infill
but factory is ABS


1986 Toyota Celica Supra Whisker Clip

Taken from: https://pinshape.com/items/16693-3d-printed-82-86-toyota-celica-supra-whisker-clip
I wanted to share this design with everyone since it's free. Give credit to Chris Halliday


1988 Toyota Supra HVAC Air Con Slider

Toyota Supra Mk3 A70 air conditioning slider component for interior climate control system.


1984 Toyota Supra Dashboard Vent

A basic vent replacement for the MK2 Supra that can be 3M taped or glued in place of the original vents if they are too brittle due to age. Replacing the stock vents is complicated since the whole dashboard has to be replaced.


1993 Toyota Supra Cover Rear Differential Oil Cooler

OEM part number 41883-14010. Split into 2 parts for easier 3D printing without support. Design not tested by creator.


2010 Toyota Generic Toyota/Lexus Hood Liner Clip

The clips that hold the acoustic liner to the hood of Toyota and Lexus vehicles are very difficult to remove without damaging the clips themselves. This is a printable replacement for these clips.


1986 Toyota Supra Radiator Pedestal Bushing

This is a direct fitment radiator lower mount bushing for the mk3 Supra. It likely fits other Toyotas of similar age. Radiator mount bushings are pretty close to all the same roughly. This is to be printed using TPU. Melting point of TPU is well above the normal radiator operating temperatures of 180-220f. I have test fitted it into the frame but have yet to install the radiator or print it in TPU yet. I started with ABS to test fit. So I don't have any print recommendations for the bushings other than I would imagine the infill will likely need to be high due to the TPU softness. I plan on trying 30% first and may end up as high as 80%, I don't know to be honest.


1986 Toyota Supra Cam Gear Locker

A simple cam gear locker with a handle, designed to fit snugly for Toyota Supra engine applications.


1986 Toyota Supra Shifter Boot Frame

I did a manual transmission swap in my MK3 Supra and needed to install a shifter boot. As I don't have the original bracket, I designed one which can be installed without the need to remove the console. Printed in PETG as PLA will surely melt in there!


2005 Toyota Camry Seat Drive Gear

Diameter 23 mm, 20 teeth, hole diameter 9 mm, height 26.5 mm.

Suitable for multiple Toyota and Lexus models, including Toyota 4runner, Alphard, Vellfire, Avensis, Camry, Highlander, Hilux, Land Cruiser, and Lexus ES300, ES330, GX470, RX330, RX350. Made by 3D printing from durable and wear-resistant PETG plastic.


Toyota V6 Engines Rear Main Seal Installer Tool

Rear main seal installer tool for Toyota V6 engines without hybrid vehicles (w/o HV). Used for installing rear main crankshaft seals.


2007 Toyota Corolla Center Console Arm Rest Hinge

The hinge for the arm rest of the center console on my 2007 Corolla broke, so I redesigned and printed a replacement that works like new. Not sure which Toyota models this will fit, so I attached a photo of the part that broke for reference. Pretty sure almost every recent Corolla uses this, maybe Camry but don't have one to reference. Hope this helps someone out there.


1990 Toyota Camry Grill Clamp

Replacement clips for the Toyota Camry grill, modeled as an exact replica. ABS material is highly recommended for this application due to heat resistance.


2008 Toyota Camry Aux to USB adapter

2-USB adapter to replace original AUX adapter. It will fit Toyota Camry 2006 - 2011. Comes from 3rd party Android Stereo for Camry.


2012 Toyota Camry USB Switch Cover

I remixed this cover from a blank version and added a custom USB port cutout. Recommended to secure with hot glue after installation.


1994 Toyota Camry Radio Knob

This is a replacement radio knob for the 1992-1996 Toyota Camry factory radio. These knobs are designed for bass/treble and balance/fade adjustments. They are prone to breaking and often go missing. Printed in PLA, two knobs are needed. The design includes knurled heads to extend from the faceplate, allowing adjustment levels when the switch is in the inward position.


2007 Toyota Camry Parking Sensor Holder

Generic Parking Sensor Holder For Toyota Camry 40 (Japan)


1998 Toyota Camry Driver's Side Sun Visor Extension

A replacement driver's side sun visor extension for a 1998 Toyota Camry.

Needs some sanding and rounding off of corners on the top and bottom to slide freely.


2005 Toyota Camry Windshield Washer Fluid Top

Cap for windshield washer fluid container. Made for 2005 Toyota Camry but may fit other Toyota models.


2005 Toyota Camry Glove Box Latch Lock

The part that breaks if you don't close the glove box carefully (too quickly). I designed this part to fit M4x12 bolts that will hold the pulls. The bolts can be purchased from an AliExpress link.


2006 Toyota Camry Glovebox Latch Clips

The glovebox never closed properly in my Aurion. The previous owner must've taken out the clips at some point to remove screws and never reinstalled them.

I could only find beige versions online for sale, They also had larger holes than the latch, so I would imagine the latch is quite sloppy in the hole.

This contains Left and Right clip STL files, They are different sizes so you can't just mirror one.

The clips print fine at .2mm, printed at 100mm/s with 70mm/s walls. 2 layer top and bottom. with accelleration at 1000mm/s on my ender 3.

I did print the final versions that I'm using at .1mm with much slower speeds, as the overhangs on the clips don't droop. Aswell as the fact that it looks much smoother aestheticly. The .2mm versions do fit and snap in correctly, if you're not worried about the aesthetics you don't need to print fine or slow.

There are a few little lips in the models as they were made in tinkercad and I couldn't be bothered cleaning them all up. They're such small lines they don't seem to print anyway.


2015 Toyota Camry Boot Release Pull Tag

Replacement internal emergency release pull tag for the trunk/boot of a 2015 Toyota Camry Hybrid (probably suits most other cars)


1979 Datsun 280ZX Sun Visor Clip

A replacement sun visor clip designed to replace the brittle original plastic part. Compatible with Datsun 280ZX. Can be printed with ASA or PETG material and should withstand the heat inside a parked car.


2017 Lexus ES 300h Speaker Adapter

This is an adapter for 6"x9" speakers compatible with the 2017 Lexus ES 300h and 350 models. The adapter was designed to fit a 254mm x 254mm print bed and can be used with specific connector adapters for easy installation.


1995 Toyota Tercel Door Trim Clip

A specialized clip used to hold the weather-stripping and upper interior door trim fascia to the metal panel for Toyota vehicles from 1990-1995. These clips are critical for preventing window glass rattling and are often difficult to replace. This 3D printable version provides an easy solution for mechanics and Toyota owners.


2008 Scion xB Grab Handle Bracket

This is a replacement grab handle bracket for my 2008 Scion xB should also fit the same year 2008 Toyota Camry. I could've bought a new handle for about 30 bucks that included the bracket. However, I figured this would be a good opportunity to learn some of the basics of Fusion 360. I've included the Fusion file if you would like to modify it. I printed the prototypes on on my Ender 3 Pro in PLA and the final on my Elegoo Mars Pro in ABS like resin. Works great! The resin I used seems to handle hot cars much better.


2022 Toyota Tundra Rear Dash Cam Clip Mount

Rear dash cam clip mount for 2022+ Tundra with full rear sliding window. Clips on to black trim. Just pull trim down, insert clip, then push trim back into place. Print in PETG to avoid warping in the sun.


1989 Toyota Camry Brightness Control Knob

This is to replace the instrument panel brightness control knob in a 1989 Toyota Camry. It can be found on the left of where the steering wheel attaches to the rest of the car. I only took into consideration the shape of the peg it had to fit onto and did not try to make this an accurate replica of the original vehicle knob. I used Tinkercad since I no longer have access to CATIA after graduating. The part is simple, consisting of just a cylinder and a square hole, so advanced CAD capabilities were not required.


1989 Toyota Camry Interior Dash Plug

Goes into slot for extra buttons on right side of steering wheel


2004 Toyota All Models Toggle Switch Holder

This is a 12mm shaft toggle switch holder for Toyota Switch blank. It fits the tall size Toyota Switch blank (40x22 mm). Print on the flat backside with support required. Updated version improves fit, makes lock nut tightening easier, and includes ON-OFF text. Compatible with multiple Toyota models including Land Cruiser, FJ Cruiser, Land Cruiser Prado, 4Runner, Tacoma, Tundra, Hilux, RAV4, Venza, Hiace, Fortuner, Sequoia, Highlander, Corolla, and Camry.


2008 Mini Cooper S Handbrake Button

This is a replacement handbrake button that fits the R56 manual transmission Mini Cooper S (and likely other manual Mini models). My button broke apart shortly after buying the car and there were zero replacement options aside from buying a new handbrake assembly. I printed this out of PETG and it works flawlessly, feels much better than the original (flatter top = better distribution of pressure). Just slide it on with the notch on top and push in the handbrake button to secure in place.


2004 Audi A4 Window Crank

Replacement window crank for Audi A4 B6. Requires some original parts for the handle and original screw. May also fit other Audi vehicles or Volkswagens.


1989 Audi Coupe Roof Light Button

The roof light button for an old Audi car that was difficult to find replacement parts for. Contains 3 parts that need to be assembled with a spring and copper part. Original Audi part number 443947105. Compatible with multiple Audi models from 1988-1997, including Coupe, 80/S2/RS2, 100/200, A6/S6, and V8 models.


2012 Audi A4 Dash Tweeter Mounts

This is to replace the factory tweeters in the dash with an aftermarket tweeter. Bolts down using the factory screws, has slight angle to prevent too much reflection of the windscreen. Factory grills fit back into place.


1990 Audi 80/Cabrio Cup Holder

This is a double cup holder for Audi 80/Cabriolet/90 etc. This fits inside the center console. Print in PETG for heat resistance.


1996 Audi A4 Front Wiper Cover Cap

Audi A4 B5 front wiper cover for the nut


2002 Mini Cooper Boost Gauge & Ultra Gauge Mount

Quick boost and ultra gauge mount for R53 tachometer


2007 Jeep Grand Cherokee Rear Wiper Cover Cap

Rear wiper pivot cover. This part was created to replace a broken cap, and it is painted in flat black for a great match.


2004 Jeep Wrangler Shift Boot Bezel

Replacement shift boot bezel for 1997-2004 Jeep Wrangler.


2004 Jeep Wrangler Cup Holder

Fits TJ and JK Wrangler models. Designed to hold most large size drinks. Installation tip: Rotate model so tab is at the top. Requires appropriate nut and bolt for recessed mounting area.


2006 Jeep Rubicon AC Knob

Replacement climate control knobs. Modeled from 2006 Rubicon knobs. Update 3-11-15: Added versions without the inside slots.


1987 Jeep Wrangler Door Lock Latch Clip

Replacement clip for holding door push rods in place. These clips can break in cold weather or with age. Designed to fit Jeep YJ models and matches Mopar part number 4658677.


2002 Jeep Wrangler Switch Panel

Custom Switch Panel for a 2002 Jeep TJ. I designed it my Junior year of high school, before I ever took a course in CAD; so be aware, the parts are an un-optimized mess. If I were you, I would immediately convert the IPT's to a solid body and start from there, maybe keep the IPT's around if you need to reference any measurements. Other than that, I'm pretty happy with how the project turned out. It fits great. I do wish that I had angled the switches more towards the driver, but with the Jeep being a manual, I was worried about accidentally hitting the switches if I extruded them out too far. But yeah that's about it. I would recommend printing in ABS if possible due to how hot it can get in a car with all the windows up. Just a suggestion :)


2007 Jeep Wrangler Door Handle Insert

These inserts fit inside door handles on a Jeep JK. You only need double-sided tape to install, potentially saving $60.00. Available as separate files for all 3 doors.


1997 Jeep Wrangler Center Console Tray

A 3D printed tray designed specifically for the 1997 Jeep TJ Wrangler. The tray features a small fillet under the lip to enable printing without supports. It may require a test print to check fit, with potential adjustments to percentage fit. Recommended to be printed in PET material with multiple shells and low infill.


2004 Mini Cooper Cup Holder Adapter

Redesigned from ground up, I removed the bottoms from both the cup holder and the adapter so you do not need any support material. The adapter is also designed not to need any too. A thin travel mug rests on the carpet, designed a riser to go inside to raise up short mugs.


2007 Mini Cooper Light Ring / Bezel Clip

This is a replacement clip for the bezel that goes around the headlight on an R57 Mini Cooper S


2005 Mini Cooper Dash Cam Mount

This provides a mount for dash cams with a 1/4" x 20tpi mounting thread. Compatible with Mobius action camera and any camera with standard tripod thread. Attaches to the bottom of the rain sensor cover using double-sided foam tape. Mounting bolt (1/4 x 20) not included.


2003 Mini Cooper Navigation Knob

Replacement part for 2003 Mini Cooper stock navigation knob


2005 Mini Cooper Wheel Liner Clip

This is a plug that replaces the OEM wheel liner clips. This is my second iteration of my design, and I will probably upload better ones at a later date. I have been replacing every one of these that I take out with my home brew design. Seems to be working well so far.


2012 MINI Countryman Wheel Well Port Cover

The cover for the access holes in a MINI Cooper Countryman wheel well.


2003 Mini Cooper Dashboard Clips

Mini Cooper/Cooper S/Cabrio dashboard mounting clip. Suitable for 3D printing on Creality Ender 3 V3 SE using PLA or PETG material. Print with supports, no raft recommended.


2002 Mini Cooper Coolant Cap

This is a coolant cap for R50 Mini Coopers. The part was 3D printed in PLA+ with 60% infill.


2004 Mini Cooper Radio Knob

Here are two different Radio Knobs for the Mini Cooper. This fits my R53 so should fit all the Mini Coopers with the same radio. You will need to reuse your metal insert no matter the design you print. I printed in PLA, but your mileage might differ.


2005 Mini Cooper Dual Relay Holder

I've just added a set of four spotlights to the front of my Cooper S R53. This requires two relays, one for each pair and a fuse. This is designed to have two relay sockets push in from underneath and a fuse holder in the front slot.
The bracket will then bolt to the front bulkhead with two self tapping screws.
Printed in PLA, 20% infill with no supports


2004 Mini Cooper Jump Start Terminal Cover

Battery terminal cover for 2001 - 2006 Mini Cooper S R53. Printed in translucent red PETG. Hold lid vertical in the open position and push down to clip on to terminal base.


2000 Mini Cooper Wheel Centre Cap

Centre Cap for Classic Mini "Minilite" alloys. Suitable for RSP Cooper, Thirty, Italian Job, Mainstream Cooper etc. There are three files, a plain centre cap plus two variant covers which can be glued to the cap if required. I have also added a Mini Club Sussex logo badge, for the guys and girls in my old club.


2002 Mini Cooper Gauge Mount

This is a mount to place a 52mm gauge beside the original revmeter of a Mini Cooper (R50/R53).


2013 Mini Cooper Cup Holder

I tried a couple similar cupholders in my 2013 Mini Cooper S, but didn't like how they fit, either in the car's cupholders or how they fit an XL soda cup or a Yeti-style coffee cup, so I designed my own version that fits my car perfectly. The smaller cup that fits into the car's cupholders still fit a soda can. Printed in PETG.


2008 Mini Cooper Hand Brake Cover Top

Designed Hand Brake cover top for my mini cooper r56 (2008), the original one was broken. Sand it, then add top coat and varnish. Use double side tape inside and press to hold it.


2000 Porsche 996 USB Mount Button

A button to replace a blank in the dash of a Porsche 996 or 986. It has an opening to mount a USB cable. I have not tried to connect a cable as I don't have one on hand and made this model on request. I can say that the button will fit as I have used a similar one I made for use with a barrel connector. The openings for the USB cable use dimensions that I'm using on other projects. The only question is if there is enough room to fit the cable from the back. You may have to trim the USB connector with an X-acto knife to fit it. There isn't room to make hollow out the back of the button without compromising the shape.


2000 Porsche 986 Dash Speaker Tweeter Clip

If you're keeping the tweeters or upgrading, these clips can be brittle now the plastic is around 20 years old.

A little different (flat backed) for easier printing but matches really well.


2002 Mini Cooper Mount for Ultragauge

This is a mount to place the Ultragauge beside the original revmeter of a Mini Cooper.


2008 Porsche 911 Grill Clip

This clip supports the mesh and slats on a Porsche 997 front bumper.

The photo shows version 1 but this STL is for version 2 which is smaller and more concealed.

Use with 3mm cable ties.

2 required per side.


1980 Mercedes L1513 Safety Belt Cap

This is a replacement part for a safety belt cap, used on some classic Mercedes Benz buses and vans. The original part came from a Mercedes 'Kurzhauber' type bus like the 911, the LA710, and L1513.


2005 Mercedes W211 Rear Wiper Window Cover

Rear window cover. In exchange for the original metal one. Stick on the glass adhesive or the sealing silicone.


1990 Mercedes W123 Switch Cover

Designed this cover for my mercedes w123 because I was missing a switch in the center console.
This cover fits perfectly in the empty slot.
It can also be used for a button or custom switch or maybe a usb charger

next version will be for a usb charger


2003 Mercedes W203 Car Clip

Plastic clips specifically designed for the Mercedes W203 trunk cover. Two variants are available: an original version and an improved version that can be inserted and removed with pliers. Printed using PETG material (recommended over PLA due to potential melting). Best printed with 'Brim' plate adhesion and suitable for 5mm holes.


1990 Mercedes W124 Mirror Adjustment Handle

Handle for Mercedes W124 driver side mirror adjustment. Also fits W123, W201, W126 models.
Disigned for 5mm rod.


2016 Mercedes C200d Cup Holder

I've done this model for my 2016 Mercedes C200d. Although I recommend you to print with PETG you can prınt with any material but PLA and other low glass transition temperature materials might deform due to the high temperatures in your car especially in summer. If you have any recommendations please write to me. My mail is "alpy.yilmaz@gmail.com".


2009 Mercedes CLK 320 Vanagon Center Cap

This is a work in progress.

Wheel center cap for the 7 spoke 16x7 Mercedes CLK 320 wheel (Mercedes part# 2094010202). This cap should fit most Mercedes wheels as well as some VW and Audi. It is designed for use on VW Vanagons to clear the front grease caps and rear axle nuts.

I designed it to (hopefully) print without the need for supports. The VW logo and the face of the cap have 2 small alignment holes to aid in assembly.


2016 Mercedes C220 Headlight Cap

Mercedes C220 Headlight Cap (2012- ?) Advantage (H7 bulbs)


2005 Nissan 350Z center cup holder

I designed this for a friend. He owns a 2005 350Z. The single (shotty) cupholder on the dash was not enough so he asked for a center console one. This is two cup holder. The driver side one is square to hold odd shaped bottles or a wallet or whatever. The piece is machine fit so it will require a rubber mallet to install. The center console will still function and close with this.


2005 Nissan 350z din bezel

double bezel for nissan 350z 06 for aftermarket chinese double din radios


2005 Nissan 350z radio bezel

Radio :                    https://amzn.eu/d/g0M3eyD
Switch:                    https://amzn.eu/d/ilUIU88
Oldschool 52mm:    https://amzn.eu/d/8b81rVd
Thermometer:          https://amzn.eu/d/66TaGei
 Mikrofaserstoff:       https://amzn.eu/d/aRglpKH


2005 Nissan 350z Clip Centre Pin

Recommended to print with high fill and thin layers in ABS or other strong material. The very top bit requires support.


2006 Nissan 350Z center console gauge panel  - replaces cubby storage

This is a replacement panel for the 350Z center console. It allows additional 3 gauges as well as relocation of the hazzard switch and the cigarette lighter from the lower dash. I've created it for my track car conversion, since most of the lower dash was being removed. Accepts up to 60mm gauges. It's a "good enough" design, will need some shims for the hazzard switch mount and drilling of the mounting tabs for screws.

For other layouts check out: https://www.thingiverse.com/thing:4247633


2006 Nissan 350z Cupholder

This is a remix of the cupholder below, essentially the same concept just that i found the circle cup holder a bit to small for the larger drinks so i just made it to where its two holes for lager drinks. This is meant to go in the center console. The center console will still function and close with this.


2005 Nissan 350Z Door Speaker Mount for JBL Door Speaker

I created this because the original 350Z Bose speakers had a mount that was built into the speaker.  The JBL door speakers needed to be mounted about 3cm from the door (they were too recessed) or the window would hit the magnet of the speaker and would not roll down all the way.


2005 Nissan 350z cubby clip tab fix

This is for the two cubbies behind the seats in the 350z. Mine came with both of the hooks broken off and missing, so I designed new ones.

Prep - use a dremel or razor to clean out and make a level spot where the broken off hook was.

Printing - I recommend using something like ABS or PETG. The model is set for PLA prototypes. When I printed using inland black PETG, it didn't work. To fix this, I multiplied the z height by 1.2 in the slicer and then it worked. I also printed with 100% infill.

Post printing - simply, clean up the part as needed. Put a drop or two of super glue and hold it there, making sure it is aligned before it dries fully.


2003 Nissan 350Z Windshield Reservoir Cap

I couldn't find a 3D model of the early model 350Z Windshield Wiper Fluid Reservoir Cap so I took some measurements and based the design on this [link](https://www.z1motorsports.com/windshield-washer/nissan/oem-350z-g35-windshield-washer-reservoir-cap-03-06-p-5557.html).

Should fit any other car that uses either 28913-JX00A or 28913-AM600.

It's a rather exact fit, so depending on your printer settings it may need +/- a few percent scale adjustment. Printing as is with PETG at 240C with .3mm layer height worked well and snapped on nicely.

4 models to choose from appropriately named.


2005 Nissan 350z Boot Hook Clip simple

A simplified boot hook clip thingy stuff. Enjoy.


2005 Nissan 350z  Door Vent Comb

I recently bought a 2005 350 base coupe, and among the various bits that are expected to be messed up on an 18-year-old entry-level sports car was the passenger door vent. Removing it revealed that the comb which connects the three vanes was missing. I took out the driver's side vent for reference and made my own. I figure if mine was broken, someone else's likely is too so I should share.

You will need 3 m2 cap head screws to fasten this to the vent body. The original uses 3 little balls that seemed like a weak spot in the design, especially for printing it, so I went with this instead. I may add another file with the original style as well later on.


2005 Nissan 350z Rear Tail Light Mounting Bolt Finishing Cap

Tight but did fit.

For

2003-2008 Nissan 350Z

2008-2015 Nissan Rogue


2005 Nissan 350Z Cubby 7inch screen holder

Disclaimer: I don't have the model for the brackets on the back.

This was originally a remix but it seems like the original model is not on Thingiverse anymore. Please make me aware of it, if its still online. I dont want to steal his stuff and not credit him.

The model is for a 350Z pre facelift interior, no idea how this fits in the facelift interior. You can melt in some thread inserts in the holes, then mount a screen. The mounting is somewhat whacky, you will have to find your own solution. I did some bracket out of scrap acrylic glass pieces, which I have molten into shape, then drilled some holes. The fitment is nowhere near perfect, but it works.

You can search for a screen on Aliexpress, pretty much any 7 inch screen that shows a Raspberry Pi on its back and has mounting holes in all 4 corners should fit. I attached a sample picture.
I am using a Raspberry Pi with OpenAutoPro, though thats discontinued at this moment. You can search for alternatives, though I have found none. For power delivery, I used this PCB: https://www.tindie.com/products/picotouch/raspberry-pi-automatic-onoff-v30-new-version/ . But thats also not being sold right now, you might find an alternative or just build it on your own with a 12V Relay.

Honest to god, I cannot find the STL for those white arms I have on my model. You need those to attach the screen holder to the center console. I dont know why I dont have them anymore, I really must have deleted them since this project is 2 years back now.

You can fabricate your own arms pretty easily with some acrylic glass. Just cut it to size and heat it with a lighter, then bend it to shape, then drill some holes in it. Or design your own arms, but that's quite some work.
Also I wanted to upload the .step file but it's bigger than 600mb and it just won't upload to thingiverse, not even after letting it sit for 2 hours.


2011 Nissan GTR Hood Latch Hook Cover 65602JK00A

This part is a recreation of the Nissan hood latch striker cover.

Nissan part # 65602JK00A

Printed this for a 2011 GT-R, should fit on 370Z, Q60, Q50, and various other Nissan models.

When installing this, insert the threaded portion into the top of the printed part otherwise it will appear not to fit.

Print in heat resistant material- ABS, PETG, Amphora, Nylon


2010 Nissan 370z upper storage bin cover

This is a cover shell for the Nissan 370z upper storage bin.


2021 Ford F-150 Morel Maximo Tweeter Mount

Mounts for Morel Maximo 6 MK II tweeters in a 2023 Ford F-150 Lightning XLT (4 speaker, no B&O). I believe it should work in any F-150 XLT 2021 to 2024, and possibly others.

An original design, but inspired by the mount by JoshFly for the 2015 F-150, which in turn was based off a design by Spincycle76


2012 Toyota Tacoma Bed rail Insert Hook

I got the anchor from: https://www.thingiverse.com/thing:2177943
I used a 5/16-18 hex nut, a 5/16-18x 1-1/4 eye bolt, a 5/16 wing nut and a washer
I break these couple times. play with the mesh a little to get a stronger design.


1994 Nissan 300ZX Cruise Control Cap

It covers the cruise control module in the engine bay.


1994 Nissan 300ZX Bose To Normal 6.5 Drivers Rear Speaker Spacer

This part raises the speaker up so that it doesn't contact the body beneath, but still fits under the stock Bose cover. Install lip side down into 6.5 adapter (uploading soon, currently sold by others on amazon)


1993 Nissan 300ZX Twinz Tt Front Valence To Na Bumper Spacer

It adapts the twinz lip to the regular na bumper buy spacing it at an angle 20+mm, creating perfect fitment.