Fog Light Bezel
2000 Pontiac Firebird 4th Gen
Description
Replace your stock fog lights on a 2000 firebird with 4.5in mishimotos or similar. Slight modification of the stock bracket is required. You need to drill 2 hole, one on each side and add some bolts. Will post pics of them installed soon. These are the ones i used. https://www.amazon.com/dp/B07CM5BGRS?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_2&th=1 Along with this glue since the lights do not have any mounting holes. Applied all around the edge. https://www.amazon.com/3M-08008-Black-Weatherstrip-Adhesive/dp/B00063X38M/ref=sr_1_1?crid=2VAEP2K4Q9N08&dib=eyJ2IjoiMSJ9.dr0kufqd6L9qR4yB0wN1jqnc0WZDiEJGmQc3Sfm2Y7s2MXCKqHXYs2HDDEFsedFRA1XUDJTrDPajFz9HwdKAoclbZ7Hq87vcDasmfqLeY3wBSwwW81wvncY1qUNZusl3bF7vh4i8xw8l8WWYOo2Svsez-w2Fuwf_zWLHlovlScAlzbCulTRtPJF1qI0_66qebVlLGjTODE_1Ic19T3qqz13P9zIj9qBV4ws7KQgnOxxa9yhNF7_xU0uv105yj2h3_GsBXf-Qa5oddy-G5CwDiUZvtyb9M4ZobWHX5QywEBI.qUDvH26OEgzCZs6l2NdXVEKdxHZgMeBh26JL_fnKWug&dib_tag=se&keywords=3m%2Bblack%2Bweatherstrip%2Badhesive&qid=1773233776&sprefix=3m%2Bblack%2Bw%2Caps%2C261&sr=8-1&th=1 Print in ASA filament is recommended to protect from UV/heat but ABS or PETG may hold up as well. I used PETG and it's been +6 months with no issues.
Print Instructions
Standard FDM printing settings: - Layer height: 0.2mm - Infill: 70% - Supports: As needed
Part Description
Replace your stock fog lights on a 2000 firebird with 4.5in mishimotos or similar. Slight modification of the stock bracket is required. You need to drill 2 hole, one on each side and add some bolts. Will post pics of them installed soon. These are the ones i used. https://www.amazon.com/dp/B07CM5BGRS?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_2&th=1 Along with this glue since the lights do not have any mounting holes. Applied all around the edge. https://www.amazon.com/3M-08008-Black-Weatherstrip-Adhesive/dp/B00063X38M/ref=sr_1_1?crid=2VAEP2K4Q9N08&dib=eyJ2IjoiMSJ9.dr0kufqd6L9qR4yB0wN1jqnc0WZDiEJGmQc3Sfm2Y7s2MXCKqHXYs2HDDEFsedFRA1XUDJTrDPajFz9HwdKAoclbZ7Hq87vcDasmfqLeY3wBSwwW81wvncY1qUNZusl3bF7vh4i8xw8l8WWYOo2Svsez-w2Fuwf_zWLHlovlScAlzbCulTRtPJF1qI0_66qebVlLGjTODE_1Ic19T3qqz13P9zIj9qBV4ws7KQgnOxxa9yhNF7_xU0uv105yj2h3_GsBXf-Qa5oddy-G5CwDiUZvtyb9M4ZobWHX5QywEBI.qUDvH26OEgzCZs6l2NdXVEKdxHZgMeBh26JL_fnKWug&dib_tag=se&keywords=3m%2Bblack%2Bweatherstrip%2Badhesive&qid=1773233776&sprefix=3m%2Bblack%2Bw%2Caps%2C261&sr=8-1&th=1 Print in ASA filament is recommended to protect from UV/heat but ABS or PETG may hold up as well. I used PETG and it's been +6 months with no issues.
Print Instructions
Standard FDM printing settings: - Layer height: 0.2mm - Infill: 70% - Supports: As needed