Cargo Cover Tonneau Clip
2018-2025 Mitsubishi Eclipse Cross
Description
Mitsubishi Eclipse Cross (2018–2025) – Cargo Cover / Trunk Tonneau Clip (Replacement STL) This is a replacement plastic clip/retainer for the cargo cover (trunk/luggage tonneau cover) on the Mitsubishi Eclipse Cross (2018–2025). It’s designed to hold the edge of the cargo cover in place on the vehicle’s side/support point, helping eliminate looseness, rattles, and vibration—just like the original part shown in the photos. ✅ Vehicle fitment: Mitsubishi Eclipse Cross 2018–2025 (please compare with your OEM part before printing) ✅ Purpose: secure/anchor the cargo cover (tonneau) in the trunk area ✅ Use case: replaces a broken/cracked/missing OEM plastic clip Installation Remove the damaged/missing clip (if still present). Place the printed part in the same position as the OEM clip. Fasten it the same way as the original (screw/clip-in, depending on your cargo cover). Test fit and adjust if needed (light sanding on contact surfaces usually solves tight fits). Print recommendations Material: PETG (recommended) or ABS/ASA (better for heat). PLA can work but may deform in hot cars. Infill: 40–70% (higher if you want it extra rigid) Perimeters/Walls: 4+ Layer height: 0.2 mm Orientation: print so the “hook/clip” area has strong layer support (avoid orientations that make the clip rely on layer adhesion alone). Post-processing: light sanding for a perfect fit. Notes Modeled from an original part and measurements from my vehicle. Small variations may exist between trims/years/production batches. If it’s too tight: sand slightly. If it’s too loose: try XY compensation in your slicer or reprint with thicker walls. Disclaimer This is an unofficial 3D-printed replacement part and is not affiliated with Mitsubishi. Use at your own risk.
Print Instructions
Standard FDM printing settings: - Layer height: 0.2mm - Infill: 70% - Supports: As needed
Part Description
Mitsubishi Eclipse Cross (2018–2025) – Cargo Cover / Trunk Tonneau Clip (Replacement STL) This is a replacement plastic clip/retainer for the cargo cover (trunk/luggage tonneau cover) on the Mitsubishi Eclipse Cross (2018–2025). It’s designed to hold the edge of the cargo cover in place on the vehicle’s side/support point, helping eliminate looseness, rattles, and vibration—just like the original part shown in the photos. ✅ Vehicle fitment: Mitsubishi Eclipse Cross 2018–2025 (please compare with your OEM part before printing) ✅ Purpose: secure/anchor the cargo cover (tonneau) in the trunk area ✅ Use case: replaces a broken/cracked/missing OEM plastic clip Installation Remove the damaged/missing clip (if still present). Place the printed part in the same position as the OEM clip. Fasten it the same way as the original (screw/clip-in, depending on your cargo cover). Test fit and adjust if needed (light sanding on contact surfaces usually solves tight fits). Print recommendations Material: PETG (recommended) or ABS/ASA (better for heat). PLA can work but may deform in hot cars. Infill: 40–70% (higher if you want it extra rigid) Perimeters/Walls: 4+ Layer height: 0.2 mm Orientation: print so the “hook/clip” area has strong layer support (avoid orientations that make the clip rely on layer adhesion alone). Post-processing: light sanding for a perfect fit. Notes Modeled from an original part and measurements from my vehicle. Small variations may exist between trims/years/production batches. If it’s too tight: sand slightly. If it’s too loose: try XY compensation in your slicer or reprint with thicker walls. Disclaimer This is an unofficial 3D-printed replacement part and is not affiliated with Mitsubishi. Use at your own risk.
Print Instructions
Standard FDM printing settings: - Layer height: 0.2mm - Infill: 70% - Supports: As needed